MEKO-free silicone sealant Kömmerling Ködisil N

  • MEKO-free and very low odour
  • Built-in fungicidal treatment
  • Available white or transparent
  • Skins over in 5 minutes

Quote

Close

Overview

          What is the Kömmerling Ködisil N silicone sealant?

    The Ködisil N is a one-component neutral cure silicone sealant that vulcanises with atmospheric moisture. What sets it apart is twofold: it is formulated without MEKO and it carries a fungicidal treatment.

     

    Most neutral silicones on the market cure through oxime and release methyl ethyl ketoxime, known as MEKO, throughout their cure — a substance classified as hazardous, which the operator breathes at the workstation. The Ködisil N releases none, and it has a very low odour. That changes the working conditions in a closed or occupied room in concrete terms.

     

    The fungicidal treatment tackles the second classic failing of a silicone joint: blackening with mould in wet areas. It keeps the bead clean for longer without reworking.

     

    The product comes in white and transparent, for a discreet bead or one matched to the substrate.

     

    Within the silicone sealant range it sits on flexible weatherproofing joints. Where the need is structural bonding or mechanical strength, the ones to look at are the polyurethane sealants or the hybrid MS polymer sealants: each family keeps its own ground.

     

    Adezif supplies this product as an official H.B. Fuller distributor, H.B. Fuller being the distributor of the Kömmerling brand.

          What is the Ködisil N used for?

    The Ködisil N is made for flexible sealing joints subject to movement, and first of all for areas where damp encourages mould.

    • Sanitary joints and kitchen equipment

    • Perimeter joints between joinery and structural work

    • Ordinary movement and expansion joints

    • Glazing and profile weather sealing

    • Cracks and transitions between dissimilar materials

    It adheres to a wide range of substrates: concrete, masonry, fibre cement, mortar, stone, ceramic, glass, steel, aluminium, wood, thermosets and many thermoplastics.

     

    Two exclusions to know. It is not suitable for PMMA. And on plastics prone to environmental stress cracking, a preliminary trial is essential: it is the plastic that fails, not the joint.

     

    The MEKO-free argument carries its full weight on work carried out in an occupied building — a public venue, a kitchen still in service, a poorly ventilated workshop — where the exposure of the operator and of the occupants is a real question.

          How is the Ködisil N sealant applied?

    The joint must measure at least 4 mm wide and 4 mm deep. Below that the bead has too little material to absorb movement and it tears.

     

    Substrates must be clean dry and degreased. On glass and metals degreasing is not optional: a residual film of grease is enough to ruin adhesion. Adezif supplies the suitable cleaners and degreasers, and the principles set out on surface preparation apply here just as they do to bonding.

     

    On wide joints, fit a foam backing rod to control the depth. The aim is to avoid three-sided adhesion: a bead bonded to the back of the joint can no longer work and splits on the first expansion cycle.

     

    Extrude with a cartridge gun. Tool the bead immediately, because the skin forms in 5 minutes: past that point tooling marks the joint instead of shaping it. Clean tools with the dedicated cleaning solvent while the sealant is still fresh.

     

    Store between +10 and +25 °C in the sealed original packaging.

          What are the technical specifications of the Ködisil N?

    The values below come from the manufacturer's documentation. They are indicative and must be confirmed by trials on your own substrates.

    FormulationMEKO-free and solvent-free
    Fungicidal treatmentYes
    TechnologyOne-component neutral cure silicone
    OdourVery low
    ColoursWhite and transparent
    Skin formation5 min
    Shore A hardness white23
    Shore A hardness transparent19
    Density white1.27 g/cm³
    Density transparent1.02 g/cm³
    ConsistencyNon-sag paste
    Temperature resistance-40 to +160 °C
    Minimum joint size4 x 4 mm
    StorageBetween +10 and +25 °C
    Packaging310 ml cartridge and 600 ml sachet

    To request the full technical data sheet or a sample of the Ködisil N, contact the Adezif team with your substrates, your joint width and the colour you need.

     

    Technical data taken from the documentation of the manufacturer Kömmerling and cross-checked against a European specialist distributor, verified on 18 November 2026. Processing values are indicative and do not remove the need for validation trials on your own substrates.

    Adezif in figures

    + 30 technical experts in industrial adhesives

    1 internal laboratory to test and validate our solutions

    + 5,000 m2 of production and storage

    + 3,000 active customers trust us